Banner D10 Series Uživatelský manuál stáhnout pdf (Strana 10)

D10 Expert

™

Dual Discrete Outputs

10 P/N 64154 rev. F

Banner Engineering Corp. • Minneapolis, MN U.S.A.

www.bannerengineering.com • Tel: 763.544.3164

Sensor Setup

•Configuressensordisplayandoperatingparameters. •ClickDynamic(+)ordouble-pulseremotelinetoselectanoption.

•Changesareupdatedinstantly. •ClickStatic(-)orsingle-pulseremotelinetoadvance.

Super-High-Speed Operation Note: Under most conditions, the sensor’s two discrete outputs operate independently. However, the outputs become complementary when

operating at Super-High-Speed, due to its extremely fast response time. Only channel 1 is taught/adjusted; channel 2 is complementary to it (output 1 conducts for the taught ON

condition, and output 2 conducts for the OFF state). To invert these conditions (output 1 – OFF condition, output 2 – ON), change light/dark operate setting.

Push Button

Remote

0.04 sec. ≤ T ≤ 0.8 sec.

Result

Access

SETUP

Mode

•Pressandhold

both buttons

concurrently for

> 2 seconds.

•Double-pulsethe

remote line.

•IndicatorArrowIcon1ONRed

Select Light/Dark

Operate

•ClickDynamic(+)to

toggle between

selections.

•Double-pulseremote

line to toggle between

selections.

Light Operate:

•Displayflashes“lo”

•Licon

Dark Operate:

•Displayflashes“do”

•Dicon

•ClickStatic(-)tosave

selection and

advance to

 “OFF-Delay.”

•Single-pulsetheremote

line to save selection

and advance to

 “OFF-Delay.”

Select OFF-Delay

Timing Enable

•ClickDynamic(+)to

toggle between

selections.

•Double-pulsetheremote

line to toggle between

selections.

OFF (No OFF-Delay):

•“t 0”

•ClockiconOFF

2 to 100 ms OFF-Delay:

•“t 2,”“t 5,”“t 10,”“t 15,”

“t 20,”“t 30,”“t 40,”

“t 60,”“t 80,”or“t100”

•ClockiconON

•ClickStatic(-)tosave

selection and

 advanceto“Display.”

•Single-pulsetheremote

line to save selection

and advance to

 “Display.”

Select Display

Parameters

•ClickDynamic(+)to

toggle between

selections.

•Double-pulsetheremote

line to toggle between

selections.

Raw signal value:

•“1234”

Percent of excess signal:

•“123P”

•ClickStatic(-)tosave

selection and advance

 to“Power/Speed.”

•Single-pulsetheremote

line to save selection

and advance to

 “Power/Speed.”

Select Speed and

Power Combination

•ClickDynamic(+)to

toggle between

selections.

•Double-pulsethe

remote line to toggle

between selections.

•IndicatorArrowIcons1and2ONRed

Super-high-speed

(50-µs response)

•“SHS” (Complementary

outputs; see note below)

High-speed

(200-µs response)

•“HS”

High-power

(1-ms response)

•“HP”

Super-high-power

(2.5-ms response)

•“SHP”

•Return

to RUN

mode.

•ClickStatic(-)to

save selection and

return to RUN mode.

•Single-pulsethe

remote line to save

selection and return

to RUN mode.

•Proceedto

Advanced

Setup

•Quad-clickStatic

(-) to proceed to

Advanced Setup.

•Quad-clickthe

remote line to

proceed to

Advanced Setup.

•SeeAdvancedSetup(page5).

TTTT

TTT

TTTT

TTT

TTTT

TTT

TTTT

TTT

TTTT

TTT

TTTT

TTT

dynamic

static

dynamic

static

dynamic

static

dynamic

static

dynamic

static

dynamic

static

TTTT

TTT

TTTT

TTT

TTTT

TTT

dynamic

static

dynamic

static

dynamic

static

dynamic

static

TTTT

TTT

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Komentáře k této Příručce

Žádné komentáře

Banner D10 Series Uživatelský manuál Strana 10

Komentáře k této Příručce

Související produkty a manuály pro Senzory Banner D10 Series