Banner A-GAGE MINI-ARRAY Series Uživatelský manuál stáhnout pdf (Strana 14)

14 P/N 43298 rev. E

Banner Engineering Corp. •Minneapolis,MNU.S.A.

www.bannerengineering.com•Tel:763.544.3164

MINI-ARRAY

InstructionManual

Installation and Mechanical Alignment

Figure 3-2. MINI-ARRAY emitter and receiver mounting bracket dimensions

Mounttheemitterandreceiverintheirmountingbrackets(showninFigure3-1),

andpositiontheredlensesofthetwounitsdirectlyfacingeachother.Theconnector

endsofbothsensorsmustpointinthesamedirection.Measurefromoneormore

referenceplanes(i.e.,thefloor)tothesamepointsontheemitterandreceiverto

verifytheirmechanicalalignment.Ifthesensorsarepositionedexactlyverticalor

exactlyhorizontal,acarpenter’slevelmaybeusefulforcheckingalignment.Extending

astraight-edgeorastringbetweenthesensorsmayhelpwithpositioning.Alsocheck

byeyeforline-of-sightalignment.Makeanynecessaryfinalmechanicaladjustments,

andhand-tightenthebrackethardware.SeeSection5forinformationonalignment

indicatorsandtheuseofthealignmentsoftwaresuppliedwiththecontroller.

Connecttheshieldedcablestotheemitterandreceiver,androutethemtothe

controllerlocation.Followthelocalwiringcodeforlow-voltagedccontrolcables.The

samecabletypeisusedforbothemitterandreceiver(twocablesrequiredpersystem).

Cutthecablestolengthaftermakingsuretheyareroutedproperly.Removecablebraid

atthecontrollerconnectionpoints(seeFigure3-4).

3.2 Controller Mounting

ThecontrollermustbeinstalledinsideanenclosurewithaNEMA(orIEC)rating

suitablefortheoperatingenvironment.

MountingdimensionsforthecontrollerareshowninFigure2-2.Thecontrolleris

suppliedwithM3.5x0.6hardwarefordirectmountingtoasurface,oritcanbe

mountedontostandard35mmDINrail.

3.3 Emitter and Receiver Hookups

Emitterandreceivercablesconnectinparalleltocontrollerterminals#4through#8.

Connectthewiresfrombothsensorcables,asfollows:

  Terminal4 Brown

  Terminal5 Blue

  Terminal6 Bare

  Terminal7 Black

  Terminal8 White

Trimoffthefoilshieldandthebraidedshieldatthepointwherethewiresexitthecable

(seeFigure3-4).

The“drainwire”istheuninsulatedstranded

wirewhichrunsbetweenthebraidedshield

andthefoilshield.Removethefoilshield

andbraidedshieldatthepointwherethe

wiresexitthecable.

Figure 3-4. Emitter/receiver cable

preparation

Tr im braided shield flush

with cable

Tr im foil shield flush

with cable

Uninsulated

drain wire

Emitter or

Receiver

8.1 mm

(0.32") max.

0.5" (13 mm) radius minimum bend

71 mm

2.8"

Figure 3-3. Quick-disconnect cable

clearances

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 43 44

Komentáře k této Příručce

Žádné komentáře

Banner A-GAGE MINI-ARRAY Series Uživatelský manuál Strana 14

Komentáře k této Příručce

Související produkty a manuály pro Senzory Banner A-GAGE MINI-ARRAY Series